Philips AEH2900/37 Manuale Utente

User manual(AEH2900, AEH2110, AEH2120, AEH2130, AEH2310)

8 EN a Status indicator b Alignment markTemperature and humidity sensorThe Temperature and humidity sensor detects the temperature and humidity at h

9ENIntelligent switchThe Intelligent switch powers on or off the connected appliance at home. a Power on/offb Power indicator c Status indicator d

10 ENSolid green for less than one secondAn event that triggers notications happens.Flashing red DisconnectedFlashing red and green alternatelyFirmwa

11EN3 SetupJoin your Smart Home network1 On your mobile device, download and install the Philips Smart Home app. 2 Follow the onscreen instructions

12 EN Note • The device exits the pairing mode after three minutes. To re-enter the pairing mode, open the battery door and close it as described in

13ENMotion sensor Door and window sensor Temperature and humidity sensor 123123123

14 ENPlug the Intelligent switchTo add the Intelligent switch to the Bridge, do the following:1 Insert the Intelligent switch into a power outlet pro

15ENResetReset network connectionReset the network connection when:• a device re-joins the Smart Home network after the batteries are replaced. • th

16 EN2 With the Philips Smart Home app, add the device to the Bridge (see 'Join your Smart Home network' on page 11). Restore factory setti

17ENTip • If you press and hold the setup button for more than six seconds, the status indicator turns off. To restore factory settings, re-do Step 1.

18 EN4 Place• Use the Smart Home devices in an indoor environment. • Keep such devices from exposure to moisture, direct sunlight, or excessive heat

19EN • In Step 2, use the screw holder for a concrete wall or surface. For a wooden surface, you can the screw only. Use the adhesive tapeYou can al

20 EN Place the Door and window sensor• Avoid the exposure to moisture and direct sunlight. • Use the alignment marks to align the two components. •

21EN 1

22 EN 2

23EN5 UsePhilips Smart Home appThrough the Philips Smart Home app you can set up the Smart Home devices, set rules of home automation, and continue to

24 ENManage devicesSet the deviceYou can edit the device information by attaching a photo and naming the location. • On the Home screen, tap the devi

25EN Delete the deviceDelete the device when:• you want to remove the device from the Bridge.• you want to restore the factory settings of the devi

26 ENSet the rules of home automationTo set a rule of home automation, set an event or time/ location as trigger. Then, set an action that is associat

27EN Edit the rules• From the Home screen, tap . Select a rule to edit or delete it.

1ENContents1 Important safety instructions 3Safety 3Important Safety Instructions 3Compliance 4Care of the environment 5Notice 5Written Offer

28 ENAccess the devices remotelyTo access your Smart Home devices remotely, log in to the portal. The rst time you log in to the portal, create your

29EN6 Check for updatesFor updates of your Smart Home devices and the Philips Smart Home app, you can receive messages on your mobile device. Follow

30 EN7 Technical dataSensors (for indoor use only)Power• Two AAA alkaline batteriesConnectivity• ZigbeeMotion sensorDetection method• Passive Infr

31EN

2015 © Gibson Innovations Limited. All rights reserved. This product has been manufactured by, and is sold under the responsibility of Gibson Innovat

2 ENPlace the Motion sensor 18Find a right location 18Use the mounting kit 18Use the adhesive tape 19Place the Door and window sensor 205 Use 23

3EN1 Important safety instructionsSafetyCAUTION: For INDOOR USE ONLY! DO NOT use this Intelligent switch with non-resistive loads, such as motors, co

4 ENCompliance Changes or modications not expressly approved by the party responsible for compliance could void the user’s authority to operate the e

5ENCare of the environmentEnvironmental informationAll unnecessary packaging has been omitted. We have tried to make the packaging easy to separate in

6 EN• The sensors and/or Intelligent switch are intended as an aid. They are not substitutes for home security supervision and should not be used as

7EN2 OverviewWith the Smart Home devices and Philips Smart Home app, you can have the changes at your home monitored, and set rules to have the connec